TSIIA Series ITEM UNIT 100 TSIIA 120 TSIIA 140 TSIIA A B A B A B Injection Unit Screw Diameter mm 36 40 40 45 40 45 Theoretical Shot Volume cm3 165 203 237 300 237 300 Shot Weight Of Injection g 231 285 332 421 332 421 Injection Stroke mm 180 210 210 Injection Pressure kg/cm2 2028 1643 2060 1628 2060 1628 Injection Rate cm3/sec 91 113 111 141 137 174 Injection Speed mm/sec 113 112 138 Screw Rotation Speed R.P.M. 304 282 278 Mold Clamping Unit Mold Clamping Force Ton 100 120 140 Mold Opening Stroke mm 300 320 345 Space Between Tie Rods (H x V) mm 360 x 360 410 x 370 410 x 410 Mold Thickness mm 120-360 130-450 130-450 Ejector Force Ton 3 3.5 3.5 Ejector Stroke mm 70 90 90 Electrical Equipment Pump Driving Motor HP 15 20 25 Heater kw 5.9 6.7 6.7 Temperature Zones zones 4 4 4 ITEM UNIT 160 TSIIA 180 TSIIA 200 TSIIA A B A B A B Injection Unit Screw Diameter mm 45 50 45 50 50 55 Theoretical Shot Volume cm3 329 406 358 442 477 577 Shot Weight Of Injection g 461 569 501 618 668 808 Injection Stroke mm 230 250 270 Injection Pressure kg/cm2 1996 1617 2189 1773 1894 1565 Injection Rate cm3/sec 142 175 139 172 179 217 Injection Speed mm/sec 113 111 115 Screw Rotation Speed R.P.M. 232 250 209 Mold Clamping Unit Mold Clamping Force Ton 160 180 200 Mold Opening Stroke mm 390 420 490 Space Between Tie Rods (H x V) mm 440 x 400 460 x 460 510 x 510 Mold Thickness mm 160-480 160-520 180-550 Ejector Force Ton 4 4 4.5 Ejector Stroke mm 115 115 130 Electrical Equipment Pump Driving Motor HP 25 30 30 Heater kw 7.6 7.6 11 Temperature Zones zones 4 4 5 ITEM UNIT 250 TSIIA 280 TSIIA 350 TSIIA A B A B A B Injection Unit Screw Diameter mm 55 60 60 65 65 70 Theoretical Shot Volume cm3 641 763 763 895 1015 1177 Shot Weight Of Injection g 898 1068 1068 1254 1421 1648 Injection Stroke mm 300 300 340 Injection Pressure kg/cm2 2101 1766 1907 1625 1746 1505 Injection Rate cm3/sec 210 250 201 236 304 353 Injection Speed mm/sec 112 109 116 Screw Rotation Speed R.P.M. 217 228 238 Mold Clamping Unit Mold Clamping Force Ton 250 280 350 Mold Opening Stroke mm 540 575 620 Space Between Tie Rods (H x V) mm 550 x 550 576 x 576 630 x 630 Mold Thickness mm 200-580 220-620 220-640 Ejector Force Ton 5 5.5 6 Ejector Stroke mm 145 160 160 Electrical Equipment Pump Driving Motor HP 40 40 50 Heater kw 14 16 20.5 Temperature Zones zones 5 5 5 * Shot weight is based on bakelite at gravity of 1.4 with power source 220V,60Hz. (Figures or color of machine are subject to change without prior notice)